1322 d st

1. Provide access to lighting boxes and termination above kitchen. Remove any insulation concealing wiring, junction boxes or lighting terminations.



2. Provide closer access to junction box above living room. Correctly splice K&T wiring to romex with protective loom or romex sleeve where it enters box. Provide equipment grounding conductor to lighting fixtures or any metallic enclosures where spliced to Knob-and-Tube wiring.Equipment grounding conductor shall be terminated to panel ground bar.



3. All romex wiring shall be secured to joists within 1 foot of box or fixture and every 4 1/2 feet maximum using romex stables.



4. All splices shall be made inside fixture or junction box. No exposed conductors. Romex cable shall be correctly terminated into box using connectors listed as such with at least 1/4” of sheathing into box.



5. Verify that new wiring to can lights is AFCI protected.



6. Provide romex to be protected from damage within 6 feet of access point. Running boards or strips 1 x2 on either side of cabling would be acceptable.



7. Driver for LED lighting shall be secured to framing members

1. Provide access to lighting boxes and termination above kitchen. Remove any insulation concealing wiring, junction boxes or lighting terminations.



2. Provide closer access to junction box above living room. Correctly splice K&T wiring to romex with protective loom or romex sleeve where it enters box. Provide equipment grounding conductor to lighting fixtures or any metallic enclosures where spliced to Knob-and-Tube wiring.Equipment grounding conductor shall be terminated to panel ground bar.



3. All romex wiring shall be secured to joists within 1 foot of box or fixture and every 4 1/2 feet maximum using romex stables.



4. All splices shall be made inside fixture or junction box. No exposed conductors. Romex cable shall be correctly terminated into box using connectors listed as such with at least 1/4” of sheathing into box.



5. Verify that new wiring to can lights is AFCI protected.



6. Provide romex to be protected from damage within 6 feet of access point. Running boards or strips 1 x2 on either side of cabling would be acceptable.



7. Driver for LED lighting shall be secured to framing members

03/23/2021

1) Obtain new permit to legalize 3rd bedroom (County Assessor’s records indicate this is a 2 bed 1 bath dwelling)

2) Provide means and access to ALL areas required for inspection purposes (expose all new J-boxes in and on the building to verify for proper termination and grounding, provide OSHA approved ladder as needed)

3) All 15A and 20A new branch circuits including any extensions greater than 6’ and devices shall be AFCI protected as required.

4) Provide required romex connectors as required throughout

5) Different gauge wiring shall not be intermixed. The power source for new lighting throughout is unknown.

6) Unapproved installation of new raceway at service panel (above busbar).

7) All #14 AWG wiring where permitted shall be protected by max 15A OCPD

8) Improper termination of conductors at service panel (double lugging of grounded conductors, different size EGC in same opening, loose wiring, etc.)

9) CO2/ smoke alarms shall be at least 3’ away from any forced air outlets including the tip of the ceiling fan blades.

10) Verify rating of outlet boxes supporting ceiling fans throughout.

11) INCOMPLETE INSPECTION



Highly recommend to obtain the services of a qualified individual to address ALL work. Too many items to list.



RECALL WHEN READY



RE-INSPECTION FEE IS WAIVED AS ONE TIME CUSTOMER COURTESY





>If inspector is unable to access all areas required for a complete inspection due to locks, obstructions or items as noted above not readily available for inspection purposes, a re-inspection fee will be assessed and new inspection request must be obtained/created with full payment of a re-inspection fee.

Cancelled by owner

03/23/2021

1) Obtain new permit to legalize 3rd bedroom (County Assessor’s records indicate this is a 2 bed 1 bath dwelling)

2) Provide means and access to ALL areas required for inspection purposes (expose all new J-boxes in and on the building to verify for proper termination and grounding, provide OSHA approved ladder as needed)

3) All 15A and 20A new branch circuits including any extensions greater than 6’ and devices shall be AFCI protected as required.

4) Provide required romex connectors as required throughout

5) Different gauge wiring shall not be intermixed. The power source for new lighting throughout is unknown.

6) Unapproved installation of new raceway at service panel (above busbar).

7) All #14 AWG wiring where permitted shall be protected by max 15A OCPD

8) Improper termination of conductors at service panel (double lugging of grounded conductors, different size EGC in same opening, loose wiring, etc.)

9) CO2/ smoke alarms shall be at least 3’ away from any forced air outlets including the tip of the ceiling fan blades.

10) Verify rating of outlet boxes supporting ceiling fans throughout.

11) INCOMPLETE INSPECTION



Highly recommend to obtain the services of a qualified individual to address ALL work. Too many items to list.



RECALL WHEN READY



RE-INSPECTION FEE IS WAIVED AS ONE TIME CUSTOMER COURTESY





>If inspector is unable to access all areas required for a complete inspection due to locks, obstructions or items as noted above not readily available for inspection purposes, a re-inspection fee will be assessed and new inspection request must be obtained/created with full payment of a re-inspection fee.

Cancelled by owner

03/23/2021

1) Obtain new permit to legalize 3rd bedroom (County Assessor’s records indicate this is a 2 bed 1 bath dwelling)

2) Provide means and access to ALL areas required for inspection purposes (expose all new J-boxes in and on the building to verify for proper termination and grounding, provide OSHA approved ladder as needed)

3) All 15A and 20A new branch circuits including any extensions greater than 6’ and devices shall be AFCI protected as required.

4) Provide required romex connectors as required throughout

5) Different gauge wiring shall not be intermixed. The power source for new lighting throughout is unknown.

6) Unapproved installation of new raceway at service panel (above busbar).

7) All #14 AWG wiring where permitted shall be protected by max 15A OCPD

8) Improper termination of conductors at service panel (double lugging of grounded conductors, different size EGC in same opening, loose wiring, etc.)

9) CO2/ smoke alarms shall be at least 3’ away from any forced air outlets including the tip of the ceiling fan blades.

10) Verify rating of outlet boxes supporting ceiling fans throughout.

11) INCOMPLETE INSPECTION



Highly recommend to obtain the services of a qualified individual to address ALL work. Too many items to list.



RECALL WHEN READY



RE-INSPECTION FEE IS WAIVED AS ONE TIME CUSTOMER COURTESY





>If inspector is unable to access all areas required for a complete inspection due to locks, obstructions or items as noted above not readily available for inspection purposes, a re-inspection fee will be assessed and new inspection request must be obtained/created with full payment of a re-inspection fee.

Cancelled by owner

03/23/2021

1) Obtain new permit to legalize 3rd bedroom (County Assessor’s records indicate this is a 2 bed 1 bath dwelling)

2) Provide means and access to ALL areas required for inspection purposes (expose all new J-boxes in and on the building to verify for proper termination and grounding, provide OSHA approved ladder as needed)

3) All 15A and 20A new branch circuits including any extensions greater than 6’ and devices shall be AFCI protected as required.

4) Provide required romex connectors as required throughout

5) Different gauge wiring shall not be intermixed. The power source for new lighting throughout is unknown.

6) Unapproved installation of new raceway at service panel (above busbar).

7) All #14 AWG wiring where permitted shall be protected by max 15A OCPD

8) Improper termination of conductors at service panel (double lugging of grounded conductors, different size EGC in same opening, loose wiring, etc.)

9) CO2/ smoke alarms shall be at least 3’ away from any forced air outlets including the tip of the ceiling fan blades.

10) Verify rating of outlet boxes supporting ceiling fans throughout.

11) INCOMPLETE INSPECTION



Highly recommend to obtain the services of a qualified individual to address ALL work. Too many items to list.



RECALL WHEN READY



RE-INSPECTION FEE IS WAIVED AS ONE TIME CUSTOMER COURTESY





>If inspector is unable to access all areas required for a complete inspection due to locks, obstructions or items as noted above not readily available for inspection purposes, a re-inspection fee will be assessed and new inspection request must be obtained/created with full payment of a re-inspection fee.

2005-12-29
JLZ
TOO MANY ITEMS - VERBAL CORRECTION TO GET STARTED.

2005-12-29
JLZ
TOO MANY ITEMS - VERBAL CORRECTION TO GET STARTED.

2005-12-29
JLZ
TOO MANY ITEMS - VERBAL CORRECTION TO GET STARTED.

2005-12-29
JLZ
TOO MANY ITEMS - VERBAL CORRECTION TO GET STARTED.

2005-04-06
PWM
31813